300 Number of packets received on this link.
301
302
303 RBYTES
304
305 Number of bytes received on this link.
306
307
308 IERRORS
309
310 Number of input errors.
311
312
313 OPACKETS
314
315 Number of packets sent on this link.
316
317
318 OBYTES
319
320 Number of bytes received on this link.
321
322
323 OERRORS
324
325 Number of output errors.
326
327
328
329 -p, --parsable
330
331 Display using a stable machine-parsable format. The -o option
332 is required with -p. See "Parsable Output Format", below.
333
334
335 -P, --persistent
336
337 Display the persistent link configuration.
338
339
340 -s, --statistics
572
573 To use the source and destination MAC addresses as well as the
574 source and destination IP addresses, the following policy can
575 be used:
576
577 -P L2,L3
578
579
580
581
582 -L mode, --lacp-mode=mode
583
584 Specifies whether LACP should be used and, if used, the mode in
585 which it should operate. Supported values are off, active or
586 passive.
587
588
589 -T time, --lacp-timer=time
590
591 Specifies the LACP timer value. The supported values are short
592 or longjjj.
593
594
595 -u address, --unicast=address
596
597 Specifies a fixed unicast hardware address to be used for the
598 aggregation. If this option is not specified, then an address
599 is automatically chosen from the set of addresses of the
600 component devices.
601
602
603
604 dladm modify-aggr [-t] [-R root-dir] [-P policy] [-L mode] [-T time]
605 [-u address] aggr-link
606
607 Modify the parameters of the specified aggregation.
608
609 -t, --temporary
610
611 Specifies that the modification is temporary. Temporary
612 aggregations last until the next reboot.
1472
1473 The delete-vlan subcommand accepts the following options:
1474
1475 -t, --temporary
1476
1477 Specifies that the deletion is temporary. Temporary deletions
1478 last until the next reboot.
1479
1480
1481 -R root-dir, --root-dir=root-dir
1482
1483 See "Options," above.
1484
1485
1486
1487 dladm show-vlan [-P] [[-p] -o field[,...]] [vlan-link]
1488
1489 Display VLAN configuration for all VLAN links or for the specified
1490 VLAN link.
1491
1492 The show-vlansubcommand accepts the following options:
1493
1494 -o field[,...], --output=field[,...]
1495
1496 A case-insensitive, comma-separated list of output fields to
1497 display. The field name must be one of the fields listed below,
1498 or the special value all, to display all fields. For each VLAN
1499 link, the following fields can be displayed:
1500
1501 LINK
1502
1503 The name of the VLAN link.
1504
1505
1506 VID
1507
1508 The ID associated with the VLAN.
1509
1510
1511 OVER
1512
2842
2843 o adv_10fdx_cap
2844
2845 o adv_10hdx_cap
2846
2847
2848 Each adv_ property (for example, adv_10fdx_cap) also has a read/write
2849 counterpart en_ property (for example, en_10fdx_cap) controlling
2850 parameters used at auto-negotiation. In the absence of Power
2851 Management, the adv* speed/duplex parameters provide the values that
2852 are both negotiated and currently effective in hardware. However, with
2853 Power Management enabled, the speed/duplex capabilities currently
2854 exposed in hardware might be a subset of the set of bits that were used
2855 in initial link parameter negotiation. Thus the MII adv_* parameters
2856 are marked read-only, with an additional set of en_* parameters for
2857 configuring speed and duplex properties at initial negotiation.
2858
2859
2860 Note that the adv_autoneg_cap does not have an en_autoneg_cap
2861 counterpart: the adv_autoneg_cap is a 0/1 switch that turns off/on
2862 autonegotiation itself, and therefore cannot be impacted by Power
2863 Management.
2864
2865
2866 In addition, the following Ethernet properties are reported:
2867
2868 speed
2869
2870 (read-only) The operating speed of the device, in Mbps.
2871
2872
2873 mtu
2874
2875 The maximum client SDU (Send Data Unit) supported by the device.
2876 Valid range is 68-65536.
2877
2878
2879 flowctrl
2880
2881 Establishes flow-control modes that will be advertised by the
2882 device. Valid input is one of:
3347 | ATTRIBUTE TYPE | ATTRIBUTE VALUE |
3348 +--------------------+-----------------+
3349 |Interface Stability | Committed |
3350 +--------------------+-----------------+
3351
3352 SEE ALSO
3353 acctadm(1M), autopush(1M), ifconfig(1M), ipsecconf(1M), ndd(1M),
3354 psrset(1M), wpad(1M), zonecfg(1M), attributes(5), ieee802.3(5),
3355 dlpi(7P)
3356
3357 NOTES
3358 The preferred method of referring to an aggregation in the aggregation
3359 subcommands is by its link name. Referring to an aggregation by its
3360 integer key is supported for backward compatibility, but is not
3361 necessary. When creating an aggregation, if a key is specified instead
3362 of a link name, the aggregation's link name will be automatically
3363 generated by dladm as aggrkey.
3364
3365
3366
3367 October 1, 2016 DLADM(1M)
|
300 Number of packets received on this link.
301
302
303 RBYTES
304
305 Number of bytes received on this link.
306
307
308 IERRORS
309
310 Number of input errors.
311
312
313 OPACKETS
314
315 Number of packets sent on this link.
316
317
318 OBYTES
319
320 Number of bytes sent on this link.
321
322
323 OERRORS
324
325 Number of output errors.
326
327
328
329 -p, --parsable
330
331 Display using a stable machine-parsable format. The -o option
332 is required with -p. See "Parsable Output Format", below.
333
334
335 -P, --persistent
336
337 Display the persistent link configuration.
338
339
340 -s, --statistics
572
573 To use the source and destination MAC addresses as well as the
574 source and destination IP addresses, the following policy can
575 be used:
576
577 -P L2,L3
578
579
580
581
582 -L mode, --lacp-mode=mode
583
584 Specifies whether LACP should be used and, if used, the mode in
585 which it should operate. Supported values are off, active or
586 passive.
587
588
589 -T time, --lacp-timer=time
590
591 Specifies the LACP timer value. The supported values are short
592 or long.
593
594
595 -u address, --unicast=address
596
597 Specifies a fixed unicast hardware address to be used for the
598 aggregation. If this option is not specified, then an address
599 is automatically chosen from the set of addresses of the
600 component devices.
601
602
603
604 dladm modify-aggr [-t] [-R root-dir] [-P policy] [-L mode] [-T time]
605 [-u address] aggr-link
606
607 Modify the parameters of the specified aggregation.
608
609 -t, --temporary
610
611 Specifies that the modification is temporary. Temporary
612 aggregations last until the next reboot.
1472
1473 The delete-vlan subcommand accepts the following options:
1474
1475 -t, --temporary
1476
1477 Specifies that the deletion is temporary. Temporary deletions
1478 last until the next reboot.
1479
1480
1481 -R root-dir, --root-dir=root-dir
1482
1483 See "Options," above.
1484
1485
1486
1487 dladm show-vlan [-P] [[-p] -o field[,...]] [vlan-link]
1488
1489 Display VLAN configuration for all VLAN links or for the specified
1490 VLAN link.
1491
1492 The show-vlan subcommand accepts the following options:
1493
1494 -o field[,...], --output=field[,...]
1495
1496 A case-insensitive, comma-separated list of output fields to
1497 display. The field name must be one of the fields listed below,
1498 or the special value all, to display all fields. For each VLAN
1499 link, the following fields can be displayed:
1500
1501 LINK
1502
1503 The name of the VLAN link.
1504
1505
1506 VID
1507
1508 The ID associated with the VLAN.
1509
1510
1511 OVER
1512
2842
2843 o adv_10fdx_cap
2844
2845 o adv_10hdx_cap
2846
2847
2848 Each adv_ property (for example, adv_10fdx_cap) also has a read/write
2849 counterpart en_ property (for example, en_10fdx_cap) controlling
2850 parameters used at auto-negotiation. In the absence of Power
2851 Management, the adv* speed/duplex parameters provide the values that
2852 are both negotiated and currently effective in hardware. However, with
2853 Power Management enabled, the speed/duplex capabilities currently
2854 exposed in hardware might be a subset of the set of bits that were used
2855 in initial link parameter negotiation. Thus the MII adv_* parameters
2856 are marked read-only, with an additional set of en_* parameters for
2857 configuring speed and duplex properties at initial negotiation.
2858
2859
2860 Note that the adv_autoneg_cap does not have an en_autoneg_cap
2861 counterpart: the adv_autoneg_cap is a 0/1 switch that turns off/on
2862 auto-negotiation itself, and therefore cannot be impacted by Power
2863 Management.
2864
2865
2866 In addition, the following Ethernet properties are reported:
2867
2868 speed
2869
2870 (read-only) The operating speed of the device, in Mbps.
2871
2872
2873 mtu
2874
2875 The maximum client SDU (Send Data Unit) supported by the device.
2876 Valid range is 68-65536.
2877
2878
2879 flowctrl
2880
2881 Establishes flow-control modes that will be advertised by the
2882 device. Valid input is one of:
3347 | ATTRIBUTE TYPE | ATTRIBUTE VALUE |
3348 +--------------------+-----------------+
3349 |Interface Stability | Committed |
3350 +--------------------+-----------------+
3351
3352 SEE ALSO
3353 acctadm(1M), autopush(1M), ifconfig(1M), ipsecconf(1M), ndd(1M),
3354 psrset(1M), wpad(1M), zonecfg(1M), attributes(5), ieee802.3(5),
3355 dlpi(7P)
3356
3357 NOTES
3358 The preferred method of referring to an aggregation in the aggregation
3359 subcommands is by its link name. Referring to an aggregation by its
3360 integer key is supported for backward compatibility, but is not
3361 necessary. When creating an aggregation, if a key is specified instead
3362 of a link name, the aggregation's link name will be automatically
3363 generated by dladm as aggrkey.
3364
3365
3366
3367 December 16, 2016 DLADM(1M)
|